ISO/TS TECHNICAL SPECIFICATION 13399-304 First edition 2016-02-01 Cutting tool data representation and exchange - Part 304: Creation and exchange of 3D models Solid milling cutters with arbor hole Représentation et échange des données relatives aux outils coupants - Partie 304: Création et échange de modeles 3D - Fraises monobloc a trou central Reference number IS0/TS13399-304:2016(E) ISO International Organization for Standardization CHEJIANG INST OF STANDARDIZATION C1 5956617 @ IS0 2016 ed without license from IHS IS0/TS 13399-304:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Licensee-ZHEJIANG INST OF STANDARDIZAISQ 0d6 - All rights reserved HS und Not for Resale, 2016/4/22 08:00:08 networking permited without license from IHS IS0/TS 13399-304:2016(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes ..2 3.1 General. .2 3.2 Reference system.. 3.3 Coordinate system at the cutting part. .3 3.4 Planes 3.5 Cutting reference point (CRP) .4 4 Design of the model .5 4.1 Necessary properties for the connection interface feature. .5 5 Plain milling cutter .6 5.1 General. .6 5.2 Necessary properties ..6 5.3 Geometry of the non-cutting part inclusive of the connection .7 5.4 Geometry of the cutting part. ..9 5.5 Plain milling cutter, complete. .9 6 Shell mill. .9 6.1 General .9 6.2 Necessary properties .10 6.3 Geometry of the non-cutting part inclusive of the connection ..10 6.4 Geometry of the cutting part.. ..10 6.5 Shell mill, complete ..10 7 Thread milling cutter. ..11 7.1 General. ..1 7.2 Necessary properties ..11 7.3 Geometry of the non-cutting part inclusive of the connection. ..12 7.4 Geometry of the cutting part. ..12 7.5 Thread milling cutter, complete ..12 8 Slotting cutter. ..12 8.1 General. ..12 8.2 Necessary properties ..13 8.3 Geometry of the non-cutting part inclusive of the connection. ..13 8.4 Geometry of the cutting part. .13 8.5 Slotting cutter, complete. ..14 9 Pointed profile slotting cutter .14 9.1 General. .14 9.2 Necessary properties .. 15 9.3 Geometry of the non-cutting part inclusive of the connection ..15 9.4 Geometry of the cutting part. ..16 9.5 Pointed profile slotting cutter. ..16 10 Flatted profile slotting cutter ..16 10.1 General. 16 10.2 Necessary properties. .17 10.3 Geometry of the non-cutting part inclusive of the connection .18 10.4 Geometry of the cutting part.. ..18 10.5 Flatted profile slotting cutter, complete. ..18 11 Concave profile cutter ..18 11.1 General. ..18 Inteainal oganzation @s1Sgr216 - All rights reserved iii Censee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 vithout license from IHS