ISO INTERNATIONAL STANDARD 366-5 First edition 2006-04-01 Textile machinery and accessories - Reeds - Part 5: Dimensions and designation of profile capsules Materielpourl'industrietextile-Peignes- Partie5:Dimensions et designationdesprofils de capsules Reference number ISO 366-5:2006(E) @ISO 2006 Copyright Intemational Organization for Standardization vithout license from IHS Not for Resale ISO366-5:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56·CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2006All rights reserved without license from IHS Not for Resale ISO 366-5:2006(E) Foreword IsO (the International Organization for Standardization)is a worldwide federation of national standards bodies (iSO member bodies). The work of preparing International Standards is normally carried out through ISO non-governmental, in liaison with IsO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO366-5 was prepared by Technical Committee ISO/Tc72, Textile machinery and accessories, SubcommitteeS 3,Machineryforfabricmanufacturing includingpreparatorymachineryandaccessories. IsO 366 consists of the following parts, under the general title Textile machinery and accessories -Reeds: Part1:Pitchboundreeds-Dimensions Part2:MetalreedswithplatebaulkDimensionsanddesignation Part 3:Metal reeds with double-springbaulk-Dimensions and designation Part4:Dimensionsanddesignationofplastic-boundmetalreeds Part5:Dimensions anddesignationofprofile capsules ii Not for Resale arda Not for Resale INTERNATIONALSTANDARD ISO366-5:2006(E) Textile machinery and accessories Reeds Part 5: Dimensions and designation of profile capsules 1 Scope This part of Iso 366 specifies the dimensions and designation of profile capsules for weaving machine reeds. These capsules are used to manufacture plastic-bound metal reeds according to Iso 366-4. Normativereferences references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Iso366-4,Textilemachineryand accessories-Reeds-Part4:Dimensionsanddesignationofplastic- boundmetalreeds Dimensions The dimensions of profile capsules shown in Figure 1 are given in Table 1. Designation The designation of profile capsules shall include the following information in the order given: a) "Profile capsule"; b) reference to this part of ISO 366, i.e. ISO 366-5; c) height of capsule, h, in millimetres; d) thickness of capsule, s, in millimetres; e) width of dent steel, b, in