BS ISO 6015:2006 Bsl Standards Publication Earth-moving machinery Hydraulic excavators and backhoe loaders Methods of determining tool forces bsi. BS ISO 6015:2006 BRITISH STANDARD Nationalforeword This British Standard is the UK implementation of IS0 6015:2006.It supersedes BS 6911-3:1990 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/513/1, Earth moving machinery (International). A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2016.Published by BSI Standards Limited 2016 ISBN9780580955211 ICS 53.100 Compliancewitha BritishStandard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2016. Amendments issued since publication Date Text affected BS ISO 6015:2006 INTERNATIONAL ISO STANDARD 6015 Second edition 2006-02-15 Earth-moving machinery Hydraulic excavatorsandbackhoeloaders Methods of determining tool forces Engins deterrassement-Pelleshydrauliqueset chargeuses-pelleteusesMethodes de determination desforces de 'outil Reference number ISO 6015:2006(E) ISO @ISO 2006 BSISO6015:2006 ISO6015:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the @ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or IsO's member body in the country of the requester. ISO copyright office Casepostale56·CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org ii @ ISO 2006 - All rights reserved BS ISO 6015:2006 ISO6015:2006(E) Contents Page 1 Scope 2 Normative references 3 Termsanddefinitions, 4 Measurementmethods 3 4.1 Test site and general .. 3 4.2 Test apparatus . 3 4.3 Preparation fortesting 4 4.4 Requirement duringtesting 8 ....... 4.5 Limit conditions 8 4.6 Pivot positions ... 8 4.7 Outriggers 8 4.8 Measurement procedure ... 8 4.9 Test report .... 10 5 Calculation methods 12 5.1 General 12 5.2 Ratedtool forces and closingforce. 12 6 Verification of rated tool and closing forces. 16 ISO 2006 - All rights reserved ili BSISO 6015:2006 ISO 6015:2006(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies non-governmental, in liaison with isO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible