BS ISO 6016:2008 BSI Standards Publication Earth-moving machinery - Methods of measuring the masses of whole machines, their equipment and components BSi raising standards worldwide" BSISO6016:2008 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 6016:2008. It supersedes BS 6911-13:1998, which is withdrawn. The UK participation in its preparation was entrusted to Technical CommitteeB/513/1,Earthmoving machinery (International) A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @BSI 2011 ISBN9780580562945 ICS 53.100 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2011. Amendments issued since publication Date Textaffected BS ISO 6016:2008 ISO INTERNATIONAL STANDARD 6016 Third edition 2008-12-01 Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and components Enginsdeterrassement-Methodesdemesuredesmassesdes enginsdeterrassementcomplets,de leurs équipements et deleurs organes constitutifs Reference number ISO 6016:2008(E) @ISO 2008 BS ISO 6016:2008 ISO6016:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT ISO2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either Iso at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2008 All rights reserved BSISO6016:2008 ISO6016:2008(E) Contents Page Foreword iv 1 Scope 2 Normative references 3 Terms and definitions.. 3.1 General definitions 3.2 3.3 Measurements 3.4 Apparatus. 4 Preparation fortesting. 5 Methods for measuring mass. 5.1 5.2 Precisionofmeasurementapparatus 5.3 Single measurement method..... 5 5.4 Cumulativemeasurementmethod. 5.5 Measurement of axle load.. 5.6 Determinationof mass ofequipment,attachmentorcomponents 8 6 Reporting measurement results.. @ IS0 2008 All rights reserved ii BS ISO 6016:2008 ISO6016:2008(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ISO 6016 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 1, Testmethodsrelatingtosafetyandmachineperformance This third edition cancels and replaces the second edition (isO 6016:1998), which has been technically re